Skip navigation
donwgentry
donwgentry Calculating status...
Currently Being Moderated

Version 9 app service still needed after upgrade to 10

Aug 20, 2012 9:01 AM

After upgrading to version 10 from 9 all was well until I turned off the version 9 Application Service.  If I do that, coldfusion stops responding (sometimes there are one or two very slow reponses followed by "Service Unavailable" messages.  Turning the version 9 Application Server service back on makes coldfusion respond normally.  All references shown via the administrator pages point to version 10 so I'm not sure what "hooks" are still pointed to version 9. 

 

Anyone else run into this situ?

615 Views   7 Replies   Latest reply: Priyank Srivastava, Apr 29, 2013 12:21 PM
 
Replies
  • Miguel-F
    Currently Being Moderated
    1. Miguel-F,
    Aug 20, 2012 9:40 AM   in reply to donwgentry
    Report

    Since you upgraded, is it just that the service name in Windows still says "9"?

    Do you have 2 windows services; one for 9 and one for 10?

     
    |
    Mark as:
  • donwgentry
    Currently Being Moderated
    2. donwgentry,
    Aug 20, 2012 10:36 AM   in reply to Miguel-F
    Report

    Yes, two Application Server services, one for 9 and one for 10.

     
    |
    Mark as:
  • Miguel-F
    Currently Being Moderated
    3. Miguel-F,
    Aug 20, 2012 10:39 AM   in reply to donwgentry
    Report

    Was that your intention?  I mean, did you want to run 9 and 10 or did you want to upgrade 9 to 10 (replacing 9)?

     
    |
    Mark as:
  • donwgentry
    Currently Being Moderated
    4. donwgentry,
    Aug 20, 2012 12:54 PM   in reply to Miguel-F
    Report

    Intent was to install 10 and remove 9.  Problem turned out to be version 9 still had its hooks in IIS until I removed the reference via configuration manager.  All is well now.  Thanks for your interest Miguel.

     
    |
    Mark as:
  • Little_Mike
    Currently Being Moderated
    5. Little_Mike,
    Aug 22, 2012 7:05 AM   in reply to donwgentry
    Report

    Correct, you want to always make sure all ISAPI modules, handler mappings, and CGI filters are removed. 

     
    |
    Mark as:
  • cewyattjr
    Currently Being Moderated
    6. cewyattjr,
    Apr 26, 2013 6:35 AM   in reply to Little_Mike
    Report

    Question though -- we are running into this same issue with the CF 10 upgrade to CF 9.  Is the installer supposed to remove these, or is it the case that you are supposed to go in and remove manually?

     

    Thanks,

     

    Chuck

     
    |
    Mark as:
  • Priyank Srivastava
    Currently Being Moderated
    7. Priyank Srivastava,
    Apr 29, 2013 12:21 PM   in reply to cewyattjr
    Report

    Best Practise is first remove the connector from your previous server(using WSCONFIG utility) which is ColdFusion 9 in this scenario, and then check IIS manager if any thing left for ColdFusion 9 which is redirecting it there, if you find anything there remove it manually.

     

    And then install ColdFusion 10 and create the connector, because if there are any left over of previous server you will face this issue.

     

    Installer of ColdFusion 10 will not remove these setting when you upgrade from ColdFusion 9 to CF 10.

     

    Regards,

    Priyank

     
    |
    Mark as:
Actions

More Like This

  • Retrieving data ...

Bookmarked By (0)

Answers + Points = Status

  • 10 points awarded for Correct Answers
  • 5 points awarded for Helpful Answers
  • 10,000+ points
  • 1,001-10,000 points
  • 501-1,000 points
  • 5-500 points